Kinco CV100 Frequency inverter - Modbus

Frequency inverter
4T : triphase 380V~440V – 50Hz/60Hz // 2S : singlephase 200V~240V
Switching frequency: 6 kHz
Output frequency: 0 - 300Hz
Frequency control: Digital, analog voltage/current
1 RS485 Modbus port
1 reference voltage output 10V - 5mA
2 analog inputs -10~+10V or 0mA~20mA
5 optocoupled multifunction digital inputs
2 analog outputs 0~10V or 0/4~20mA
1 optocoupled open collector output 30V - 50mA
1 relay output, 250VAC - 2A, 30VDC - 1A
1 power supply output +24V - 200 mA

130.00 € Without Taxes 130.0 EUR 130.00 €

130.00 €

156.00 € 156.00 € with taxes

  • Brand
  • Voltage
  • Inputs
    • 5
  • Analog inputs
  • Analog outputs
  • Interface
  • Drive power

This combination does not exist.

Product Documents

CV100 Spécifications
Manuel CV100

Features


Power : 200W - 400W - 750W - 1500W - 2200W

Carrier Frequency up to 15kHz

Output Frequency : 0 - 300Hz

Auto torque boost and auto slip compensation function

Built-in PID control

Auto standbye function

Wall mounting

 

1 RS485 Modbus port

1 10v reference voltage output

2 analog inputs -10~+10V

5 digital multi-function input, Optocoupler isolation

2 analog output 0~10V or 0/4~20mA

1 optocoupled output, open collector 30V - 50mA

1 relay output, 250VAC - 2A, 30VDC - 1A

1 power supply output  +24V - 200 mA

 

External dimensions <= 1500W : 

W : 85 mm

H : 142 mm

D : 122 mm

Weight: 0.8 kg

 

External dimensions   2200W : 

W: 101 mm

H : 152 mm

D : 127 mm

Weight : 1 kg

 

Features

ItemDescription
Input Rated voltage and frequency 4T : triphase 380V~440V – 50Hz/60Hz // 2S : singlephase 200V~240V

Allowable voltage range 4T : 320V~460V // 2S : 180V~260V -  Voltage unbalancedness <3 % - Frequency +-5 %
Output Rated Voltage 0~Rated input voltage
Frequency 0Hz~300Hz
Overload capacity Type G : 150 % 1 mn – 180 % 10 s
Controle method Mode V/F
Starting torque Auto torque rising
Frequency accuracy Digital setting : max. frequency x +- 0.01% – Analog setting : max. frequency x +-0.2 %
Frequency resolution Digital setting : 0.01Hz – Analog setting : max. frequency x 0.05 %
Torque boost Manual torque boost : 0% ~ 30.0 %
V/F patterns 4 patterns : 1 V/F curve mode set by user and 3 kinds of torque- derating modes (2.0 power - 1.7 power - 1.2 power)
Acc/Dec curves Linear/deceleration. Four kinds of acceleration/deceleration time
Auto current limit Limit current durinf operation automatically to prevent
Operation command Keypad setting – Terminal setting – Communication setting Integrated screen - Inputs - Modbus
Frequency command Digital setting – analog voltage setting – analog current setting
Auxiliary frequency setting Implement flexible auxiliary frequency trim and frequency synthesis
Analog output 2 channel analog output (0/4~20mA or 0/2~10V)
Protection functions
Overcurrent protection - overvoltage protection – undervoltage protection – overheat protection – overload protection – missing phase protection (selectable) and so on
Environnement Use Indoor - installed in the environnement free from direct sunlight – dust – corrosive gas – combustible gas – oil mist – steam and drip
Altitude Derated above 1000m – the rated output current shall be decreased by 10% for every rise of 1000m
Ambient temperature -10°C~40°C - derated at 40°C~50°C
Humidity 5%~95%RH – non-condensing
Vibration Less than 5.9m/s2 (0.6g)
Storage temperature -40°C~70°C
Structure Protection class IP20
Cooling method Air cooling with fan control
Installation method Wall mounting
Efficiency ≥ 93 %


 

Connections

Category MarkingDescription
GND for the shield PE GND for the shield
Power Supply +10 +10V power supply Reference Voltage +10V – 5mA
OP +24V power supply for small equipments 24V 200mA max.
Communication RS+ / RS- port RS485 Use twisted-pair or shield cable
Analog input AI1 and AI2 Analog single-ended Analog voltage or current input – mode selected by jumpers AI1/AI2 (Reference ground : COM) ) – Voltage range -10V~+10V (Input resistor 45kOhm) Resolution 1/4000 – Current range 0mA~20mA Resolution 1/2000 (jumper select)
Analog output A01 and AO2
Providing analog voltage or current selected by jumper AO1/AO2 – The default setting is output voltage refer to to the function code A6.28/A6.29 (Reference ground : COM) - Voltage range 0V~10V – Current range 0/4mA~20mA
Multifonction input terminal X1~X5
Can be defined as multi-function digital input terminal – Refer to description of function code A6.00~A6.04 (A6 group) – Optocoupler isolation input – input resistor 3.3kOhm – Input voltage range of X1~X5 : 2~30V
Multifonction output terminal Y1 Bi-direction open collector output Can be defined as multi-function digital ouput terminal – Refer to description of function code A6.00~A6.04/A6.14 (A6 group) – Optocoupler isolation output – Max. working voltage : 30Vmax. Current 50mA
Common port COM
Common port of 24V power supply.  Cooperate with other terminals.




Specifications

Drive power 200 W or 400 W or 750 W or 1500 W or 2200 W
Brand Kinco
Voltage 230 VAC
Inputs 5
Analog inputs 2
Analog outputs 2
Interface Modbus RS485
Your Dynamic Snippet will be displayed here... This message is displayed because you did not provided both a filter and a template to use.