Servodrive 200 to 750W

Servodrive 200 to 750W

Servodrive / positioner

  • Compatible with 200W, 400W and 750W servomotors
  • Torque mode, Speed mode
  • Position mode, Pulses/direction mode
  • Master Slave mode
  • Slave encoder output

More details...

296,04 € tax incl.

246,70 €tax excl.

CD420-AA-000

The CD420 servodrive is equiped with the same step/direction command interface as stepper driver.

He is also equiped with an analog command interface in torque, speed mode and a slave encoder output.

The CD420's inputs/outpust made easy to use the driver for automatic cycle applications.

An included homing function usually available on high range drivers can be used to create standalone applications.

Pre-registered recipes parameters are available for the SMH80 and SMH110 motors series.


Setup of the CD420 is really simple with the KincoServo software the configuration cable from Kinco

  Manual

  Servomotors and Servovariators Documentation

Model CD420
Power Main supply voltage Single-phase AC220V±20% 47~63Hz
Control circuit voltage DC24V 1A
Current Rated current(RMS) 4A
Peak current(PEAK) 15A
Feedback signal 2500PPR (incremental encoder with 5V supply and RS422 signals)
Brake chopper Use an external braking resistor if necessary
Brake chopper threshold DC380V±5V
Over-voltage alarming threshold DC400V±5V
Under-voltage alarming threshold DC200V±5V
Cooling method Natural air cooling
Weight 1.2kg
Position
Mode
Max. frequency of input pulse Differential signal: 500KPPS, Open-collector signal: 200KPPS
Pulse command mode Pulse+direction, CCW+CW, (higher voltages than 5V need external current limiting resistors)
Command smoothing Low-pass filtering(Internal parameters)
Feedforward gain Internal parameters
Electronic gear ratio Setting range, Gear factor: -32768~32767, Gear divider: 1~32767, 1/50≤|Gear factor/Gear divider|≤50
Position loop sampling frequency 1KHz
Speed
Mode
Analog input voltage range 0 ~±10V(Resolution 12bit)
Input impedance 200K
Analog input sampling frequency 4KHz
Command source External analog command/internal command
Command smoothing Low-pass filtering(Internal parameters)
Input voltage dead-zone setting Internal parameters
Input voltage offset settiong Internal parameters
Speed limit Internal parameters
Torque limit Internal parameters / External analog command control
Speed loop sampling frequency 4KHz
Torque
Mode
Analog voltage input range 0 ~±10V (Resolution 12bit)
Input impedance 200K
Input sampling frequency 4KHz
Command source External analog command/internal command
Command smoothing Low-pass filtering(Internal parameters)
Speed limit Internal parameters /External analog command control
Input voltage dead-zone setting Internal parameters
Input voltage offset setting Internal parameters
Current sampling frequency 16KHz
Digital
Input
Input specification 7 digital inputs, with COMI terminal for PNP or NPN connection.
Input function Define freely according to requirement, supporting following functions: Driver enable,driver fault reset,driver mode control,Proportional control, forward inhibit limit, reverse inhibit limit, negative limit position,home signal, speed command reverse, internal speed or position select 
Digital
Onput
Output specification 5 digital outputs,OUT1?OUT4 current is 100mA,OUT5 current is 800mA
Output function Define freely according to requirement, supporting following functions: Driver ready, driver fault, position reached, motor at zero speed, motor brake, motor speed reached, N signal
Protection functions Over-voltage protection,under-voltage protection,motor over-heat protection(I²T),short-circuit protection,drive over-heat protection,etc.
Communication interface RS232
Operation
Environment
Operating temperature 0~40?
Storage temperature -10?~70?
Humidity(non-condensing) 5~95%
Protection class IP20
Installation environment Installed in a dust-free,dry and lockable environment(such as in a electrical cabinet)
Installation mode Vertical installation
Height Below 1000m
Atmospheric pressure 86kpa~106kpa

No customer reviews for the moment.

Write your review

Servodrive 200 to 750W

Servodrive 200 to 750W

Servodrive / positioner

  • Compatible with 200W, 400W and 750W servomotors
  • Torque mode, Speed mode
  • Position mode, Pulses/direction mode
  • Master Slave mode
  • Slave encoder output

Write your review

7 other products in the same category :