2CM545 Digital stepper driver - 50V 4.5A Kinco

Driver 2CM545
- 50V 4.5A
- 8 levels of current adjustment from 2.4~8A
- 15 levels of resolution from 200~25,600 steps
- Inputs (Pulses/Dir or CW/CCW) 5~24V optocoupled with integrated limiting resistor, TTL compatible
- Pulse input frequency up to 400KHz
- Motor parameters self-identification system
- Automatic current reduction in case of inactivity
- Overvoltage and overcurrent protection

78.00 € Without Taxes 78.0 EUR 78.00 €

78.00 €

93.60 € 93.60 € with taxes

  • Brand
  • Max. Voltage
  • Max. current
  • Resolution setting
  • Weight

This combination does not exist.

En rupture de stock

Internal Reference: 2CM545

2CM545 Microstep driver

 

  • 8 levels of current adjustment from 1~4.5A
  • 15 step resolution from 200~25,600 steps
  • Inputs (Pulses/Dir or CW/CCW) 5~24V optocoupled with integrated limiting resistor, TTL compatible
  • Pulse input frequency up to 400KHz
  • Self-identification system of motors parameters for optimum operation
  • automatic current reduction in case of inactivity
  • Rotation test
  • Overvoltage and overcurrent protection
  • "Multi-stepping" system to optimize management of micro-stepping mode and therefore reduce vibrations. The driver will thus break down the steps in an optimum manner according to the speed of rotation.
  • Compatible with Nema 23 motors

Item

Description
Input voltage 24~50VDC
Over voltage protection 85VDC
Undervoltage protection 15VDC
Overheat protection 80°C (Temperature of thermistor)
Current per Phase (peak) 1/1.5/2/2.5/3/3.5/4/4.5 A – 8 adjustable values
Step resolution 200~25600 Pulses / tour - 15 adjustable valuess
Motor range Nema 23
Control signal inputs PLS (CW) - DIR (CCW) – FREE – Input voltage : 5~24VDC – Input current : 8mA@5VDC / 12mA@24VDC
Control modes Pulse control : PLS + DIR – CW/CCW
Output signal ERR - open collector output – maximum current: 100mA
Indications of operation Combination of the different states of the RUN and ERR LEDs
Protective Circuits Under voltage – Over voltage – Over current
Cooling Natural ambiant air
Environment Indoors - sheltered from: direct sunlight / dust / corrosive and flammable gases / vapors / splashes
Humidity <85%RH – non-condensing
Ambient temperature 0°C~40°C
Storage temperature -20°C~70°C
Protection sign IP20
Resolution setting (Pulses/Turn)Current setting (A)
SW1 SW2 SW3 SW4=ON SW4=OFF SW6 SW7 SW8 RMS Peak
ON ON ON 200 1000 ON ON ON 3.2 4.5
OFF ON ON 400 2000 OFF ON ON 2.8 4
ON OFF ON 800 4000 ON OFF ON 2.5 3.5
OFF OFF ON 1600 5000 OFF OFF ON 2.1 3
ON ON OFF 3200 8000 ON ON OFF 1.8 2.5
OFF ON OFF 6400 10000 OFF ON OFF 1.4 2.0
ON OFF OFF 12800 20000 ON OFF OFF 1.1 1.5
OFF OFF OFF 25600 NA OFF OFF OFF 0.7 1.0

Function

DIP Position

Description
PLS + DIR SW6 & SW7 = ON – Others OFF Driver off, set DIP switches to enable required functions. Switch on the driver: the RUN Led flashes GREEN and the ERR Led is RED, this means that the settings have been taken into account. Turn off the driver and replace the DIP switches to return to normal operation.
CW/CCW SW7 & SW8 = ON – Others OFF
Micro-Step smoothing and dynamics filter disabled SW5 & SW6 = ON – Others OFF
Micro-Step smoothing filter enable SW5 & SW7 = ON – Others OFF
Micro-Step dynamics filter activation SW5 & SW8 = ON – Others OFF
Power-on motor parameter test disable SW6 & SW7 & SW8 = ON – Others OFF
Power-on motor parameter test enabled SW5 & SW6 & SW7 = ON – Others OFF
Rotation test SW6 & SW8 = ON – Others OFF Rotation at 80 rpm
Automatic current reduction SW5 = ON – Others OFF Set SW5=ON to enable automatic current reduction. The current is reduced to half of the set current 1.5s after the motor stops




Accessories

Your Dynamic Snippet will be displayed here... This message is displayed because you did not provided both a filter and a template to use.


Specifications

Brand Kinco
Max. Voltage 50 V
Max. current 4.5 A
Resolution setting DIP-switches
Weight 280 gr
Your Dynamic Snippet will be displayed here... This message is displayed because you did not provided both a filter and a template to use.